Yealink SIP-T21 Uživatelský manuál stáhnout pdf

Accessing the web user interface:

Account Settings: Click on Account->Register->Account X (X=1,2)

Parameters of the account:

Network Settings:

Account Settings:

Configuring via phone user interface

Configuring via web user interface

Configuring Your Phone

SIP-T21P & SIP-T21

Enterprise IP Phone

Quick Installation Guide

www.yealink.com

Note: Please locate your computer in the same network segment of the IP phone (192.168.0.X) to access

the web user interface. Contact your system administrator for more information.

Note: Check with your system administrator if any error appears during the registration process or a

specific configuration is required for your registration.

Note: The wrong network settings may result in inaccessibility of the phone and may have an impact on

the network performance. Contact your system administrator for more information.

1. Press the OK key when the phone is idle to get the IP address of the phone.

You can configure the network in the following ways:

It shows the register status of the current account.

You can select Enabled/Disabled to enable/disable the account.

It is shown on the LCD to identify the account.

It is shown as caller ID when placing a call.

It is provided by ITSP for registration (required).

It is an authenticated ID for authentication provided by ITSP (required).

It is provided by ITSP for registration (required).

DHCP: By default, the phone attempts to contact a DHCP server in your network to obtain its

valid network settings, e.g., IP address, subnet mask, gateway address and DNS address.

Static IP Address: If the phone cannot contact a DHCP server for any reason, you need to

configure IP address, subnet mask, gateway address, primary DNS address and

secondary DNS address for the phone manually.

PPPoE: If you are using an xDSL modem, you can connect your phone to the Internet via PPPoE

mode. Contact the ITSP for the user name and password.

Press the Menu soft key when the phone is idle, select Settings->Advanced Settings

(password:admin)->Network->WAN Port/VLAN/Webserver Type/802.1x Settings/VPN to configure

the network.

For more information, refer to the User Guide available online:

http://www.yealink.com/SupportDownloadfiles_detail.aspx?CateId=333&flag=142

Press the Menu soft key when the phone is idle, select Settings->Advanced Settings

(password:admin)->Accounts to configure the account.

2. Open the web browser on your computer, enter the IP address into the address bar

(e.g., "http://192.168.0.10" or "192.168.0.10") and press Enter.

Line Active:

Label:

Display Name:

User Name:

Password:

Server Host:

3. Enter the user name (default: admin) and password (default: admin) in the login page

and click Confirm.

Network Settings: Click on Network->Basic->IPv4 Config

Note: For more information on account parameters, refer to Configuring via web user interface.

Registered Register Failed Registering

Applies to firmware version 72.1 or later.

1 2

Shrnutí obsahu

Strany 1 - Enterprise IP Phone

Accessing the web user interface:Account Settings: Click on Account->Register->Account X (X=1,2)Parameters of the account:Network Settings:Acco

Strany 2 - Assembling the Phone

Startup1. Attach the stand, as shown below:2. Connect the handset and optional headset, as shown below:3. Connect the network and power, as shown belo

Příbuzné modely SIP-T21P

Další dokumenty pro Kabelové telefony Yealink SIP-T21

Zobrazit dokument Yealink SIP-T21 Uživatelský manuál

Yealink SIP-T21 Uživatelský manuál (142 stránky)

Komentáře k této Příručce

Žádné komentáře

Yealink SIP-T21 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Kabelové telefony Yealink SIP-T21. Yealink SIP-T21 User Manual Uživatelská příručka

Shrnutí obsahu

Příbuzné modely SIP-T21P

Další dokumenty pro Kabelové telefony Yealink SIP-T21

Komentáře k této Příručce

Související produkty a manuály pro Kabelové telefony Yealink SIP-T21